| Three-body abrasive wear behaviour of metastable spheroidal carbide cast irons with different chromium contents |
6 |
| Influence of dislocations on precipitation processes in hot-extruded Al-Mn-Sc-Zr alloy |
5 |
| Mechanical and morphological properties of bamboo mesoparticle/nylon 6 composites |
5 |
| Thermodynamic re-assessment of the binary Cr-Ta system down to 0 K |
5 |
| Experimental investigation of gas/slag/matte/tridymite equilibria in the Cu-Fe-O-S-Si system in controlled gas atmosphere at T=1200 degrees C and P(SO2)=0.1 atm |
5 |
| Low-temperature sintering of 0.96(K0.5Na0.5)NbO3-0.04LiNbO(3) lead-free piezoelectric ceramics modified with CuO |
5 |
| Phase transitions in copper-silver alloys under high pressure torsion |
4 |
| Experimental liquidus studies of the Zn-Fe-Si-O system in air |
4 |
| Microstructure and properties of Cu-bearing carbidic austempered ductile iron |
4 |
| Effect of V and Zr microalloying, and heat treatment on microstructure and mechanical properties of secondary Al-7Si-3Cu-0.3Mg alloy |
4 |
| Fabrication of bioactive porous bredigite (Ca7MgSi4O16) scaffold via space holder method |
4 |
| Abrasive wear resistance of modified X37CrMoV5-1 hot work tool steel after conventional and laser heat treatment |
3 |
| Deformation response and microstructural evolution of as-cast Mg alloys AM30 and AM50 during hot compression |
3 |
| Microstructure and mechanical properties of ultra-fine WC-10Co cemented carbides with Cr3C2 and NbC: Experimental investigation supported by thermodynamic calculation |
3 |
| Dendritic solidification of highly undercooled dilute alloys |
2 |
| Thermodynamic investigations in the Al-Fe system: Thermodynamic modeling using CALPHAD |
2 |
| Intermetallic precipitation in rare earth-treated A413.1 alloy: A metallographic study |
2 |
| Biomedical porous Ti-16Nb-10Zr-(0-15)Ta alloys |
2 |
| Particle and microstructural characteristics in the coarse-grained heat-affected zone of Al-Ti-Ca complex deoxidized steels |
2 |
| Deposition of CVD-TiCN and TiAlN coatings guided with thermodynamic calculations |
2 |
| Isothermal sections of the Co-Ni-Ti system at 950 and 1000 degrees C |
2 |
| Photocatalytic properties of nano-structured carbon nitride: a comparison with bulk graphitic carbon nitride |
2 |
| Statistical analysis of micropore size distributions in Al-Si castings evaluated by X-ray computed tomography |
2 |
| 3D nanoflower-structured TiO2 photoanode for efficient photoelectrochemical water splitting |
2 |
| Dynamic mechanical behavior of magnesium alloys: a review |
2 |
| Dendritic structure formation of magnesium alloys for the manipulation of corrosion properties: Part 1-microstructure |
2 |
| First evidence of grain boundary serration in a specifically heat treated wrought Alloy 625 Ni-based superalloy |
2 |
| Effect of B4C in Ti-6Al-4V matrix on workability behavior of powder metallurgy composites during cold upsetting |
2 |
| Effect of lubricant additives on the tribological behavior of aluminum alloy against steel |
2 |
| Hot torsion behavior of SP-700 near beta titanium alloy in single and dual phase regions |
2 |
| Microstructural evolution, phase selection and properties of CoCrCuFeMnxNi high-entropy alloys |
2 |
| Solid-state synthesis and magnetic properties of rhombohedral phase Mg2SiNi3 |
2 |
| Microstructure and oxidation of Ni-Fe2O3 composite coating on AISI 304 stainless steel |
2 |
| An artificial intelligence paradigm in heuristic search of tensile behaviour of titanium alloys |
2 |
| Effects of graphene nanoplatelets on the tribological, mechanical, and thermal properties of Mg-3Al alloy nanocomposites |
2 |
| Microstructure and properties of laser interference crystallized amorphous FeSiB ribbon |
2 |
| Analysis of amorphous regions in severely marformed NiTi shape memory alloy |
2 |
| Microstructure and selected mechanical and electrical property analysis of Sr-doped LaCoO3 perovskite thin films deposited by the PLD technique |
2 |
| Evolution of gamma ' morphology and gamma/gamma ' lattice parameter misfit in a nickel-based superalloy during non-equilibrium cooling |
2 |
| The structure and formation mechanism of FeS2/Fe3S4/S-8 nanocomposite synthesized using spherical shaped Fe3O4 nanoparticles as the precursor |
2 |
| Effect of heat treatment on the precipitation hardening in FeNiCoAlTaB shape memory alloys |
2 |
| Thermodynamic description of the Cu-S-Sn system |
2 |
| Ultrathin SnO2 nanorod/reduced graphene oxide nanosheet composites for electrochemical supercapacitor applications with excellent cyclic stability |
2 |
| Surface morphology and phase stability of titanium irradiated with 168 MeV Xe-136 ions |
2 |
| Microstructural effects of isothermal aging on a doped SAC solder alloy |
2 |
| Grain size gradient naturally prepared through recrystallization in rapidly solidified undercooled alloy melts |
2 |
| Severe shot peening of AISI 321 with 1000% and 1300% coverages: A comparative study on the surface nanocrystallization, phase transformation, sub-surface microcracks and microhardness |
2 |
| Effect of coupled annular electromagnetic stirring and intercooling on the microstructures macrosegregation and properties of large-sized 2219 aluminum alloy billets |
2 |
| Structure and corrosion resistance of titanium oxide layers produced on NiTi alloy in low-temperature plasma |
2 |
| Synthesis and characterization of magnesium-based hybrid composites - A review |
1 |
