| Modeling reoxidation behavior of Al-Ti-containing steels by CaO-Al2O3-MgO-SiO2 slag |
9 |
| On significance of initial microstructure in governing mechanical behavior and fracture of dual-phase steels |
7 |
| Influence of slip ratio on worn-surface microstructure and fatigue wear behavior of D2 wheel steel |
6 |
| Combination of cold drawing and cryogenic turning for modifying surface morphology of metastable austenitic AISI 347 steel |
6 |
| Effect of Mg addition on formation of intragranular acicular ferrite in heat-affected zone of steel plate after high-heat-input welding |
6 |
| Prevention of carbon migration in 9% Cr/CrMoV dissimilar welded joint by adding tungsten inert gas overlaying layer |
5 |
| Effects of Al addition on bainite transformation and properties of high-strength carbide-free bainitic steels |
5 |
| Cavity formation in cross-wedge rolling processes |
5 |
| Interlayer engineering for titanium clad steel by hot roll bonding |
5 |
| Aluminum, titanium and oxygen control during electroslag remelting of stainless steel based on thermodynamic analysis |
4 |
| Comparison of microstructure and mechanical properties of titanium/steel composite plates by two manufacturing processes |
4 |
| Review of non-reactive CaO-Al2O3-based mold fluxes for casting high-aluminum steel |
4 |
| Solidification structure refinement of ferritic stainless steel based on heterogeneous nucleation technology |
4 |
| Modification mechanism of caking and coking properties of Shenmu subbituminous coal by low-temperature rapid pyrolysis treatment |
4 |
| Effect of vacuum level on microstructure and mechanical properties of titanium-steel vacuum roll clad plates |
4 |
| Strengthening granulation behavior of specularite concentrates based on matching of characteristics of iron ores in sintering process |
4 |
| Effect of coarse TiN inclusions and microstructure on impact toughness fluctuation in Ti micro-alloyed steel |
4 |
| Constitutive modeling and critical strain of dynamic recrystallization in SA508Gr.4N steel for advanced pressure vessel materials |
4 |
| Effect of M-A constituents formed in thermo-mechanical controlled process on toughness of 20CrNi2MoV steel |
4 |
| Effect of cooling rate and composition on microstructure and mechanical properties of ultrahigh-strength steels |
4 |
| Microscopic damage mechanism of SA508 Gr3 steel in ultra-high temperature creep |
3 |
| Microstructure evolution and mechanical properties of 316L austenitic stainless steel with aluminum addition by warm rolling |
3 |
| Characterization of hot deformation behavior of wear-resistant steel BTW1 using processing maps and constitutive equations |
3 |
| Effect of hot rolling and cooling process on microstructure and properties of 2205/Q235 clad plate |
3 |
| Discrete element method study of solid descending and residence properties in COREX shaft furnace with center gas supply device |
3 |
| A new method to predict mechanical properties for microalloyed steels via industrial data and mechanism analysis |
3 |
| In situ observation and modeling of austenite grain growth in a Nb-Ti-bearing high carbon steel |
3 |
| A method for observing tridimensional morphology of sulfide inclusions by non-aqueous solution electrolytic etching |
3 |
| Comparative cyclic oxidation behaviour and effect of oxides on hardness of wear resistance coating alloys T-401 and T-900 |
3 |
| On microstructure characterization of Fe-Cr-Ni-Mo-N super-austenitic stainless steel during hot deformation |
3 |
| Effect of time interval on microstructure evolution of medium carbon steel during warm deformation |
3 |
| Pyrometallurgical recycling of stainless steel pickling sludge: a review |
3 |
| Extraction of iron and aluminum from high-iron bauxite by ammonium sulfate roasting and water leaching |
3 |
| Numerical simulation on characteristics of COREX shaft furnace with central gas distribution |
3 |
| Corrosion and passive behaviour of duplex stainless steel 2205 at different cooling rates in a simulated marine-environment solution |
3 |
| Effect of Al2O3/SiO2 and CaO/Al2O3 ratios on wettability and structure of CaO-SiO2-Al2O3-based mold flux system |
3 |
| Effect of W addition on hot deformation and precipitation behaviors of 19Cr2Mo ferritic stainless steel |
3 |
| Recent advances of nanoporous metal-based catalyst: synthesis, application and perspectives |
3 |
| Anomalous residual austenite formation in root of welding layers of 9% Cr/CrMoV dissimilar welded joint |
3 |
| Microstructure and mechanical behavior of a low-density Fe-12Mn-9Al-1.2C steel prepared using centrifugal casting under near-rapid solidification |
3 |
| Application of tellurium in free-cutting steels |
3 |
| Insights on pretreatment of Indian hematite fines in grate-kiln pelletizing process: the choice of grinding processes |
3 |
| Recent progress in friction stir welding tools used for steels |
3 |
| Austenite transformation and work hardening of medium manganese steel |
3 |
| Influence of particle size on combustion behavior of bamboo char used for blast furnace injection |
3 |
| Effect of shot peening on microstructure, nanocrystallization and microhardness of Ti-10V-2Fe-3Al alloy surface |
3 |
| Effect of milling duration on hydrogen storage thermodynamics and kinetics of ball-milled Ce-Mg-Ni-based alloy powders |
3 |
| Effects of Zr addition on evolution behavior of inclusions in EH36 shipbuilding steel: from casting to welding |
3 |
| Optimal design of hot rolling process for C-Mn steel by combining industrial data-driven model and multi-objective optimization algorithm |
3 |
| Effect of laser shock peening on combined low- and high-cycle fatigue life of casting and forging turbine blades |
3 |
