| Experimental analysis of spatter generation and melt-pool behavior during the powder bed laser beam melting process |
41 |
| Influence of SLM process parameters on the surface finish, porosity rate and fatigue behavior of as-built Inconel 625 parts |
40 |
| The effects of forced interpass cooling on the material properties of wire arc additively manufactured Ti6Al4V alloy |
31 |
| Texture control of 316L parts by modulation of the melt pool morphology in selective laser melting |
31 |
| Additive manufacturing using WAAM with AA5183 wire |
30 |
| The influence of build parameters and wire batch on porosity of wire and arc additive manufactured aluminium alloy 2319 |
30 |
| Evaluation of grinding process using simultaneously MQL technique and cleaning jet on grinding wheel surface |
30 |
| The influence of process parameters on vertical surface roughness of the AlSi10Mg parts fabricated by selective laser melting |
29 |
| Critical influences of particle size and adhesion on the powder layer uniformity in metal additive manufacturing |
28 |
| Scaling laws for the additive manufacturing |
28 |
| Effects of printing parameters of fused deposition modeling on mechanical properties, surface quality, and microstructure of PEEK |
27 |
| Microstructure and mechanical properties of double-wire plus arc additively manufactured Al-Cu-Mg alloys |
27 |
| Micro-fabrication of high aspect ratio periodic structures on stainless steel by picosecond direct laser interference patterning |
24 |
| General investigations on processing tool steel X40CrMoV5-1 with selective laser melting |
24 |
| Analysis of processing parameters and characteristics of selective laser melted high strength Al-Cu-Mg alloys: From single tracks to cubic samples |
24 |
| Investigation of the Lorentz-force-driven sheet metal stamping process for cylindrical cup forming |
23 |
| Comparison between the improvements made to the fatigue strength of stainless steel by cavitation peening, water jet peening, shot peening and laser peening |
22 |
| Thermal behavior of the molten pool, microstructural evolution, and tribological performance during selective laser melting of TiC/316L stainless steel nanocomposites: Experimental and simulation methods |
22 |
| Influences of process parameters on surface roughness of multi-layer single-pass thin-walled parts in GMAW-based additive manufacturing |
21 |
| Turning of Inconel 718 with whisker-reinforced ceramic tools applying vegetable-based cutting fluid mixed with solid lubricants by MQL |
21 |
| Influence of selective laser melting process parameters on texture evolution in pure copper |
21 |
| Density and mechanical properties in selective laser melting of Invar 36 and stainless steel 316L |
20 |
| Experimental study on drilling load and hole quality during rotary ultrasonic helical machining of small-diameter CFRP holes |
19 |
| Thermal modeling and characterization of wire arc additive manufactured duplex stainless steel |
19 |
| Heat transfer simulations of selective laser melting process based on volumetric heat source with powder size consideration |
18 |
| Numerical modeling of melt-pool behavior in selective laser melting with random powder distribution and experimental validation |
18 |
| Characterization of Inconel 625 fabricated using powder-bed-based additive manufacturing technologies |
18 |
| Additive manufacturing of NiTi shape memory alloys using pre-mixed powders |
18 |
| Joining of aluminum alloy and polymer via friction stir lap welding |
17 |
| Investigation on evolution mechanisms of site-specific grain structures during metal additive manufacturing |
17 |
| Laser polishing of additive manufactured CoCr alloy components with complex surface geometry |
17 |
| Investigation on influences of initial residual stress on thin-walled part machining deformation based on a semi-analytical model |
17 |
| Role of evolving microstructure on the mechanical behaviour of P92 steel welded joint in as-welded and post weld heat treated state |
16 |
| Cutting performance of textured polycrystalline diamond tools with composite lyophilic/lyophobic wettabilities |
16 |
| Investigation of process factors affecting mechanical properties of INCONEL 718 superalloy in wire plus arc additive manufacture process |
16 |
| Effect of printing parameters in 3D concrete printing: Printing region and support structures |
16 |
| Lap joining of TC4 titanium alloy to 304 stainless steel with fillet weld by GTAW using copper-based filler wire |
15 |
| Numerical design of high depth-to-width ratio friction stir welding |
15 |
| Surface finish control of additively-manufactured Inconel 625 components using combined chemical-abrasive flow polishing |
15 |
| Effect of processing conditions on the microstructure, porosity, and mechanical properties of Ti-6Al-4V repair fabricated by directed energy deposition |
15 |
| Corrosion and tribocorrosion behaviour of Ti6Al4V produced by selective laser melting and hot pressing in comparison with the commercial alloy |
14 |
| Novel drill bit based on the step-control scheme for reducing the CFRP delamination |
14 |
| The double-wire feed and plasma arc additive manufacturing process for deposition in Cr-Ni stainless steel |
14 |
| Micro-mechanism of central damage formation during cross wedge rolling |
14 |
| Evaluation of novel tool geometries in dry drilling aluminium 2024-T351/titanium Ti6Al4V stack |
14 |
| Enhanced machinability of SiC-reinforced metal-matrix composite with hybrid turning |
14 |
| Effects of duplex jets high-pressure coolant on machining temperature and machinability of Ti-6Al-4V superalloy |
14 |
| Enhanced beads overlapping model for wire and arc additive manufacturing of multi-layer multi-bead metallic parts |
14 |
| Densification behavior of pure Zn metal parts produced by selective laser melting for manufacturing biodegradable implants |
14 |
| Heat propagation of circular thin-walled parts fabricated in additive manufacturing using gas metal arc welding |
14 |
