| Evaluation of machinability and economic performance in cryogenic-assisted hard turning of alpha-beta titanium: a step towards sustainable manufacturing |
13 |
| Mechanistic modeling of cutting forces in micro-end-milling considering tool run out, minimum chip thickness and tooth overlapping effects |
10 |
| Modeling of machined surface characteristics in cryogenic orthogonal turning of inconel 718 |
9 |
| Machining of NiTi-shape memory alloys-A review |
8 |
| Enhancing the machining performance by cutting tool surface modifications: a focused review |
8 |
| Experimental characterization and finite element modeling of critical thrust force in cfrp drilling |
7 |
| Evaluation of performance of nanofluid using multiwalled carbon nanotubes for machining of Ti-6AL-4V |
6 |
| Simulation and experimental investigations into abrasive flow nanofinishing of surgical stainless steel tubes |
6 |
| Comparative evaluations of machining performance during turning of 17-4 PH stainless steel under cryogenic and wet machining conditions |
6 |
| How cryogenic techniques help in machining of nickel alloys? A review |
5 |
| On the effect of relative size of magnetic particles and abrasive particles in MR fluid-based finishing process |
5 |
| Turning induced residual stress prediction of AISI 4130 considering dynamic recrystallization |
5 |
| Development and machinability evaluation of MgO doped Y-ZTA ceramic inserts for high-speed machining of steel |
5 |
| Numerical simulation of the effects of elastic anisotropy and grain size upon the machining of AA2024 |
4 |
| Machining of sintered steel under different lubrication conditions |
4 |
| Design of the cross-structural cathodes in electrochemical machining of aero-engine blades |
4 |
| A review on the conventional, non-conventional, and hybrid micromachining of glass |
3 |
| Development of magnetorheological fluid-based process for finishing of ferromagnetic cylindrical workpiece |
3 |
| Experimental investigation of tool wear and machining rate in rotary ultrasonic machining of nickel alloy |
3 |
| Comparative analysis of chipping mechanics of float glass during rotary ultrasonic drilling and conventional drilling: For multi-shaped tools |
3 |
| Experimental investigation of top burr formation in high-speed micro-end milling of titanium alloy |
3 |
| An analytical approach to cutting force prediction in milling of carbon fiber reinforced polymer laminates |
3 |
| A new reverse engineering method to combine FEM and CFD simulation three-dimensional insight into the chipping zone during the drilling of Inconel 718 with internal cooling |
3 |
| Development and experimental validation of a mechanistic model of cutting forces in micro- ball end milling of full slots |
3 |
| Investigation into fabrication of microslot arrays by electrochemical micromachining |
3 |
| Temperature measurement and machining damage in slotting of multidirectional CFRP laminate |
3 |
| Performance enhancement of cryogenic machining and its effect on tool wear during turning of Al-Tic(p) composites |
3 |
| Experimental evaluation on the effect of electrostatic minimum quantity lubrication (EMQL) in end milling of stainless steels |
3 |
| Investigation into erosion rate of AISI 4340 steel during wire electrical discharge turning process |
3 |
| Investigation into the performance of eco-friendly graphite nanofluid as lubricant in MQL grinding |
3 |
| Edge micro-creation of Ti(C, N) cermet inserts by micro-abrasive blasting process and its tool performance |
3 |
| Effect of thermal properties on laser cutting of continuous glass and carbon fiber-reinforced polyamide 6 composites |
3 |
| Experimental investigation of surface roughness and cutting ratio in a spraying cryogenic turning process |
2 |
| Study of saw-tooth chip in machining of Inconel 718 by metallographic technique |
2 |
| Role of stabilizers on agglomeration of debris during micro-electrical discharge machining |
2 |
| An investigation of the hole machining processes on woven carbon-fiber reinforced polymers (CFRPs) using abrasive waterjets |
2 |
| Surface integrity in broaching of AA 7075-T651 aluminum alloys |
2 |
| Surface roughness modeling in Laser-assisted End Milling of Inconel 718 |
2 |
| Study on the influence of meso-geometrical features on milling force in precision machining of titanium alloy |
2 |
| Comparison of drilled hole quality evaluation in CFRP/CFRP stacks using optical and ultrasonic non-destructive inspection |
2 |
| Effects of friction conditions on the formation of dead metal zone in orthogonal cutting - a finite element study |
2 |
| An integrated prediction model for the dynamics of machine tool spindles |
2 |
| Improvements in the thread cutting torque for a 6082-T6 aluminum-based alloy with tapping tools utilizing diamond coating |
2 |
| Differential finishing of freeform surfaces (knee joint) using R-MRAFF process and negative replica of workpiece as a fixture |
2 |
| A micromechanics analysis of the material removal mechanisms in the cutting of ceramic particle reinforced metal matrix composites |
2 |
| Stability charts with large curve-flute end-mills for thin-walled workpieces |
2 |
| A gun drill mechanics model analysis based on 15-5PH solid solution stainless steel |
2 |
| Prediction of cutting force for ball end mill in sculptured surface based on analytic model of CWE and ICCE |
2 |
| Modeling surface roughness for polishing process based on abrasive cutting and probability theory |
2 |
| Implementation of analytical boundary simulation method for cutting force prediction model in five-axis milling |
1 |
