| Multiple-jet electrospinning methods for nanofiber processing: A review |
25 |
| Experimental study on mechanical drilling of carbon/epoxy composite-Ti6Al4V stacks |
18 |
| Performance evaluation of Al2O3 nano powder mixed dielectric for electric discharge machining of Inconel 825 |
15 |
| Stationary shoulder tool in friction stir processing: a novel low heat input tooling system for magnesium alloy |
15 |
| Investigation on the cutting quality characteristics of abrasive water jet machining of AA6061-B4C-hBN hybrid metal matrix composites |
15 |
| Processing of materials at cryogenic temperature and its implications in manufacturing: A review |
15 |
| Particulate metal matrix composites and their fabrication via friction stir processing - a review |
15 |
| Comparative study of the effect of surface texturing on cutting tool in dry cutting |
14 |
| Effect of friction stir welding process parameters on Mg-AZ31B/Al-AA6061 joints |
14 |
| A review of processing techniques for graphene-reinforced metal matrix composites |
13 |
| Experimental investigation on wire electric discharge machining (WEDM) of Nimonic C-263 superalloy |
13 |
| Issues and strategies in composite fabrication via friction stir processing: A review |
13 |
| Influence of various metal powder mixed dielectric on micro-EDM characteristics of Ti-6Al-4V |
12 |
| Direct-write 3D printing of NdFeB bonded magnets |
12 |
| Processing issues, machining, and applications of aluminum metal matrix composites |
12 |
| Procedure to convert phosphogypsum waste into valuable products |
12 |
| A comparison between wet and cryogenic drilling of CFRP/Ti stacks |
12 |
| PECVD process parameter optimization: towards increased hardness of diamond-like carbon thin films |
12 |
| Microhole drilling through electrochemical processes: A review |
12 |
| Experimental investigation into the effects of nozzle position, workpiece hardness, and tool type in MQL turning of AISI 1045 steel |
12 |
| Friction stir processing of Al6061-SiC-graphite hybrid surface composites |
12 |
| On pressurized feeding approach for effective control on working gap in ECDM |
12 |
| Multiobjective optimization and analysis of copper-titanium diboride electrode in EDM of monel 400 alloy |
11 |
| Effect of ultrasonic vibration on the single discharge of electrochemical discharge machining |
11 |
| An environment-friendly and sustainable machining method: near-dry EDM |
11 |
| Cutting force and hole quality analysis in micro-drilling of CFRP |
10 |
| Pulse and direct electrodeposition of Ni-Co/micro and nanosized SiO2 particles |
10 |
| A comprehensive study on surface integrity of nickel-based superalloy Inconel 718 under robotic belt grinding |
10 |
| Effect of tool rotation in near-dry EDM process on machining characteristics of HSS |
10 |
| Joining of metal matrix composites using friction stir welding: a review |
10 |
| EDM of Ti-6Al-4V: Electrode and polarity selection for minimum tool wear rate and overcut |
10 |
| Assessment of drilling-induced damage in CFRP under chilled air environment |
10 |
| A comparison between vibration assisted and conventional drilling of CFRP/Ti6Al4V stacks |
10 |
| Investigation of minimum quantity lubrication effects in drilling CFRP/Ti6Al4V stacks |
10 |
| Study the parametric effect of abrasive water jet machining on surface roughness of Inconel 718 using RSM-BBD techniques |
10 |
| Enhancing corrosion resistance of Al-Cu/AZ31 composites synthesized by a laser cladding and FSP hybrid method |
9 |
| Effect of cryogenic minimum quantity lubrication on machinability of diamond tool in ultraprecision turning of 3Cr2NiMo steel |
9 |
| Optimization of A-TIG process parameters using response surface methodology |
9 |
| Experimental investigation on drilling of natural flax fiber-reinforced composites |
9 |
| Synthesis of polishing fluid and novel approach for nanofinishing of copper using ball-end magnetorheological finishing process |
9 |
| A study on the effect of polishing fluid volume in ball end magnetorheological finishing process |
9 |
| WEDM of Mg/CRT/BN composites: Effect of materials and machining parameters |
9 |
| Experimental investigation of dry, wet and cryogenic boring of AA 7075 alloy |
9 |
| Machinability analysis of high strength materials with Cryo-Treated textured tungsten carbide inserts |
9 |
| Investigation of magnetic field-assisted EDM of composites |
8 |
| Eccentric-weave FSW between Cu and AA 6061-T6 with reinforced Graphene nanoparticles |
8 |
| WEDM process parameter optimization of FSPed copper-BN composites |
8 |
| Bio-inspired low elastic biodegradable Mg-Zn-Mn-Si-HA alloy fabricated by spark plasma sintering |
8 |
| Activated flux TIG welding of Inconel 718 super alloy in presence of tri-component flux |
8 |
| Surface characteristics of mild steel using EDM with Cu-MWCNT composite electrode |
8 |
