| Internal unsteady flow characteristics of centrifugal pump based on entropy generation rate and vibration energy |
12 |
| Analysis of natural convective flow of non-Newtonian fluid under the effects of nanoparticles of different materials |
11 |
| The effect of pulsating throughflow on the onset of magneto convection in a layer of nanofluid confined within a Hele-Shaw cell |
10 |
| Experimental investigations on R430A as a drop-in substitute for R134a in domestic refrigerators |
10 |
| Design and development of submerged arc welding fluxes using TiO2-SiO2-CaO and SiO2-CaO-Al2O3 flux system |
8 |
| Effects of Cu-Ag hybrid nanoparticles on the momentum and thermal boundary layer flow over the wedge |
6 |
| Entropy generation and heat transport analysis of Casson fluid flow with viscous and Joule heating in an inclined porous microchannel |
6 |
| Comparative investigation of auxiliary processes for increasing the strength of clinched joints |
6 |
| Aiding and opposing of mixed convection Casson nanofluid flow with chemical reactions through a porous Riga plate |
5 |
| Impact of viscosity variation on oblique flow of Cu-H2O nanofluid |
5 |
| Application of artificial bee colony algorithm for maximizing heat transfer in a perforated fin |
5 |
| Impact of magnetic dipole on a thermally stratified ferrofluid past a stretchable surface |
5 |
| Analysis of mixing performances in microchannel with obstacles of different aspect ratios |
4 |
| Characteristics optimization of powder mixed electric discharge machining using titanium powder for die steel materials |
4 |
| Investigation of machining characterization for wire wear ratio & MRR on pure titanium in WEDM process through response surface methodology |
4 |
| Magnetohydrodynamic convection in a porous square cavity filled by a nanofluid with viscous dissipation effects |
4 |
| Assembly sequence planning using soft computing methods: A review |
4 |
| Experimental investigations and statistical modeling of surface roughness during ultrasonic-assisted turning with self-lubricating cutting inserts |
4 |
| FE simulation of linear and elliptical ultrasonic vibrations in turning of Inconel 718 |
4 |
| Modeling of surface roughness in the magnetorheological cylindrical finishing process |
4 |
| Theoretical and numerical modeling of tool-chip friction in ultrasonic-assisted turning |
4 |
| A modified firefly algorithm to maximize heat dissipation of a rectangular porous fin in heat exchangers exposed to both convective and radiative environment |
3 |
| Rotor profile design and numerical analysis of 2-3 type multiphase twin-screw pumps |
3 |
| Cross-fuzzy entropy-based approach for performance degradation assessment of rolling element bearings |
3 |
| Experimental and numerical investigation of the transient characteristics and volute casing wall pressure fluctuations of a single-blade pump |
3 |
| Multiple slip effects on magnetic-Carreau fluid in a suspension of gyrotactic microorganisms over a slendering sheet |
3 |
| Entropy generation of tangent hyperbolic nanofluid flow past a stretched permeable cylinder: Variable wall temperature |
3 |
| Generalization of the tetraparametric assembly method for the optimization of bolt tightening sequences in ring-type joints |
3 |
| Numerical investigation of fluid flow and heat transfer characteristics in novel circular wavy microchannel |
3 |
| Multicriteria optimization of mechanical properties of aluminum composites reinforced with different reinforcing particles type |
3 |
| Numerical and experimental study of the impact of conical chimney angle on the thermodynamic characteristics of a solar chimney power plant |
3 |
| Experimental studies on graphite powder-mixed electro-discharge machining of Inconel 718 super alloys: Comparison with conventional electro-discharge machining |
3 |
| Formability of aluminum 5083 friction stir welded blank in two-point incremental forming process |
2 |
| Crosswise stream of methanol-iron oxide (CH3OH-Fe3O4) with temperature-dependent viscosity and suction/injection effects |
2 |
| Energy-efficient hydraulic actuator position tracking using hydraulic system operation modes |
2 |
| Research on multi-objective optimization of switched flux motor based on improved NSGA-II algorithm |
2 |
| Multi-shaped tool wear study during rotary ultrasonic drilling and conventional drilling for amorphous solid |
2 |
| Analysis of mixed convection past a heated sphere |
2 |
| An analytical model of burnishing forces using slab method |
2 |
| Modeling and prediction of metallic powder behavior in explosive compaction process by using genetic programming method based on dimensionless numbers |
2 |
| Thermal and water ageing effect on mechanical, rheological and morphological properties of glass-fibre-reinforced poly(oxymethylene) composite |
2 |
| The theoretical and experimental research on the thermodynamic process in transcritical carbon dioxide piston compressor |
2 |
| Time-varying stiffness model of spur gear considering the effect of surface morphology characteristics |
2 |
| A novel method to design pressure compensator for variable displacement axial piston pump |
2 |
| Ductilizing of cast hypereutectic Al-17%Si alloy by friction stir processing |
2 |
| Study on warm forming effects of the axial-pushed incremental rolling process of spline shaft with 42CrMo steel |
2 |
| Oscillatory dissipative conjugate heat and mass transfer in chemically reacting micropolar flow with wall couple stress: A finite element numerical study |
2 |
| Investigation of the physical and mechanical properties of Ni-P and Ni-P-PTFE nanocomposite coatings deposited on aluminum alloy 7023 |
2 |
| Automated laser engraving system for the calibration and manufacturing of nonlinear scales for electrical measuring instruments |
2 |
| Numerical analysis of transient characteristics of a bulb hydraulic turbine during runaway transient process |
2 |
