| Phase field modelling of crack propagation, branching and coalescence in rocks |
75 |
| Modeling of rheological fracture behavior of rock cracks subjected to hydraulic pressure and far field stresses |
74 |
| Determination of the stress field and crack initiation angle of an open flaw tip under uniaxial compression |
52 |
| Application of an average strain energy density criterion to obtain the mixed mode fracture load of granite rock tested with the cracked asymmetric four-point bend specimens |
29 |
| 3-D X-ray computed tomography on failure characteristics of rock-like materials under coupled hydro-mechanical loading |
26 |
| Crack coalescence behavior of sandstone specimen containing two pre-existing flaws under different confining pressures |
23 |
| A computational approach for crack identification in plate structures using XFEM, XIGA, PSO and Jaya algorithm |
23 |
| Crack initiation angles and propagation paths in polyurethane foams under mixed modes I/II and I/III loading |
22 |
| Synergistic effects of hybrid MWCNT/nanosilica on the tensile and tribological properties of woven carbon fabric epoxy composites |
19 |
| Fatigue strength of blunt V-notched specimens produced by selective laser melting of Ti-6Al-4V |
18 |
| The effect of agglomeration on the fracture toughness of CNTs-reinforced nanocomposites |
18 |
| Cracking elements method for dynamic brittle fracture |
16 |
| Experimental and numerical investigations of concrete behaviour at meso-level during quasi-static splitting tension |
16 |
| Analysis of transient dynamic fracture parameters of cracked functionally graded composites by improved meshfree methods |
15 |
| Linking microstructure and processing defects to mechanical properties of selectively laser melted AlSi10Mg alloy |
15 |
| Dynamic damage localization in crack-weakened rock mass: Strain energy density factor approach |
15 |
| Finite element modeling strategies for 2D and 3D delamination propagation in composite DCB specimens using VCCT, CZM and XFEM approaches |
14 |
| Experimental and numerical study of granite blocks containing two side flaws and a tunnel-shaped opening |
14 |
| Failure characteristics of intermittent fissures under a compressive-shear test: Experimental and numerical analyses |
14 |
| Statistical analysis of concrete fracture using normal distribution pertinent to maximum aggregate size |
13 |
| Characterisation of fatigue crack growth using digital image correlation measurements of plastic CTOD |
12 |
| Wedge-splitting tests for tensile strength and fracture toughness of concrete |
12 |
| On predicting mode II fracture toughness (K-IIc) of hot mix asphalt mixtures using the strain energy density criterion |
12 |
| On the evaluation of fracture fatigue entropy |
11 |
| Fracture studies of Ultra-High Performance Concrete using dynamic Brazilian tests |
11 |
| On Brazilian disk test for mixed-mode I/II fracture toughness experiments of anisotropic rocks |
11 |
| Determination of fracture parameter and prediction of structural fracture using various concrete specimen types |
11 |
| Surface roughness effect on multiaxial fatigue behavior of additive manufactured metals and its modeling |
11 |
| Phase-field models for fatigue crack growth |
11 |
| Phase field fracture in elasto-plastic solids: Abaqus implementation and case studies |
11 |
| Using acoustic emission technique to monitor damage progress around joints in brittle materials |
10 |
| Study of interaction effects of asymmetric cracks under biaxial loading using digital photoelasticity |
10 |
| Time-dependent reliability assessment of fatigue crack growth modeling based on perturbation series expansions and interval mathematics |
9 |
| On the strength prediction of adhesively bonded FRP-steel joints using cohesive zone modelling |
9 |
| Application of rice husk biochar and thermally treated low silica rice husk ash to improve physical properties of cement mortar |
9 |
| Interfacial toughening of carbon/epoxy composite by incorporating styrene acrylonitrile nanofibers |
9 |
| Lightweight construction materials: Mortar reinforced with date-palm mesh fibres |
9 |
| Comparison between cohesive zone and coupled criterion modeling of crack initiation in rhombus hole specimens under quasi-static compression |
9 |
| On the fatigue behavior of additive manufactured lattice structures |
9 |
| Effect of interface fiber angle on the mode I delamination growth of plain woven glass fiber-reinforced composites |
9 |
| The fracture behaviour of nanostructure added adhesives under ambient temperature and thermal cyclic conditions |
9 |
| A review of the extended finite element method on macrocrack and microcrack growth simulations |
9 |
| Fatigue life assessment of notched round bars under multiaxial loading based on the total strain energy density approach |
9 |
| Fracture load prediction under mixed mode I plus II using a stress based method for brittle materials tested with the asymmetric four-point bend specimen |
9 |
| Mode II modeling of adhesive materials degraded by fatigue loading using cohesive zone elements |
9 |
| A micromechanical model for prediction of mixed mode I/II delamination of laminated composites considering fiber bridging effects |
9 |
| Frequency characteristics of the released stress wave by propagating cracks in brittle materials |
9 |
| Effects of support friction on mode I stress intensity factor and fracture toughness in SENB testing |
9 |
| Experimental determination of the notch stress intensity factor for sharp V-notched specimens by using the digital image correlation method |
9 |
| Fabrication and evaluation of silica aerogel-epoxy nanocomposites: Fracture and toughening mechanisms |
8 |
