| A COMPARATIVE STUDY OF GRAPHITE GROWTH IN CAST IRON AND IN ANALOGOUS SYSTEMS |
11 |
| Preparation of Fiber-Reinforced Shell by Airflow Placement Fiber Technology for Investment Casting |
8 |
| DEVELOPMENT AND EVALUATION OF A NEW ECO-FRIENDLY SODIUM SILICATE-BASED BINDER SYSTEM |
7 |
| EXPERIMENTAL INVESTIGATIONS ON THE INFLUENCE OF THE THERMAL CONDITIONS DURING COMPOSITE CASTING ON THE MICROSTRUCTURE OF Cu-Al BILAYER COMPOUNDS |
7 |
| Re-Thinking Design Methodology for Castings: 3D Sand-Printing and Topology Optimization |
7 |
| EFFECT OF SAMARIUM (SM) ADDITION ON THE MICROSTRUCTURE AND TENSILE PROPERTIES OF Al-20%Si CASTING ALLOY |
6 |
| Enhancing the Permeability and Properties of Ceramic Shell in Investment Casting Process Using ABS Powder and Needle Coke |
6 |
| Effect of Firing Temperature and Time on Hybrid Fiber-Reinforced Shell for Investment Casting |
6 |
| 3D PRINTED SMART MOLDS FOR SAND CASTING |
6 |
| Effect of Pouring Conditions and Gating System Design on Air Entrainment During Mold Filling |
6 |
| ON THE INTERPRETATION OF MELT QUALITY ASSESSMENT OF A356 ALUMINUM ALLOY BY THE REDUCED PRESSURE TEST: THE BIFILM INDEX AND ITS PHYSICAL MEANING |
5 |
| The Use of Stirring Methods for the Production of SiC-Reinforced Aluminum Matrix Composite and Validation Via Simulation Studies |
5 |
| SIMULATION OF FLUIDITY AND MISRUN PREDICTION FOR THE CASTING OF 356.0 ALUMINUM ALLOY INTO SAND MOLDS |
5 |
| EFFECT OF RARE EARTH METALS ON POROSITY FORMATION IN A356 ALLOY |
4 |
| HYDROUS SOLID SILICATES IN NEW FOUNDRY BINDERS |
4 |
| EFFECT OF Sr-GRAIN REFINING-Si INTERACTIONS ON THE MICROSTRUCTURAL CHARACTERISTICS OF Al-Si HYPOEUTECTIC ALLOYS |
4 |
| INFLUENCE OF CARBIDE-PROMOTING ELEMENTS ON THE PEARLITE CONTENT AND THE TENSILE PROPERTIES OF HIGH SILICON SSDI DUCTILE IRON |
4 |
| Thermal Decomposition Studies of EPS Foam, Polyurethane Foam, and Epoxy Resin (SLA) as Patterns for Investment Casting; Analysis of Hydrogen Cyanide (HCN) from Thermal Degradation of Polyurethane Foam |
4 |
| Microsilica in Sodium Silicate Bonded Sands |
4 |
| Friction Stir Processing of Aluminum Alloy A206: Part IITensile and Fatigue Properties |
4 |
| Revealing the As-Cast and Homogenized Microstructures of Niobium-Bearing Nickel-Based Superalloy |
4 |
| Modification of Hypereutectic Al-20wt%Si Alloy Based on the Addition of Yttrium and Al-5Ti-1B Modifiers Mixing Melt |
4 |
| Integrated System of Thermal/Dimensional Analysis for Quality Control of Gray and Ductile Iron Castings Solidification |
3 |
| PARAMETERS DETERMINATION OF GRAIN MICROSTRUCTURE PREDICTION FOR A SINGLE CRYSTAL CASTING SIMULATION AND ITS EXPERIMENTAL VALIDATION |
3 |
| MICROSTRUCTURE AND MECHANICAL PROPERTIES OF AZ61 MAGNESIUM ALLOYS WITH THE Y AND Ca COMBINED ADDITION |
3 |
| Effect of Alloy Composition on Microstructure and Tensile Properties of Net-Shaped Castings of Al-Zn-Mg-Cu Alloys |
3 |
| Optimisation of Dry Sliding Wear Parameters of Squeeze Cast AA336 Aluminium Alloy: Copper-Coated Steel Wire-Reinforced Composites by Response Surface Methodology |
3 |
| Influences of Rod Diameter and Sand-Mould Strength on Hot Tearing in Mg WE43A Constrained Rod Castings |
3 |
| Ultrasonication Effects on the Microstructure Characteristics of the A380 Die Cast Alloy |
3 |
| Thermal Analysis and Production of As-Cast Al 7075/6060 Bilayer Billets |
3 |
| EFFECT OF beta-AL(5)FESI AND pi-AL(8)MG(3)FESI(6) PHASES ON THE IMPACT TOUGHNESS AND FRACTOGRAPHY OF AL-SI-MG-BASED ALLOYS |
3 |
| EFFECT OF SOLIDIFICATION ENVIRONMENT ON MICROSTRUCTURE AND INDENTATION HARDNESS OF Al-Zn-Mg ALLOY CASTS DEVELOPED USING MICROWAVE HEATING |
3 |
| EFFECT OF DEGASSING AND GRAIN REFINEMENT ON HOT TEARING TENDENCY IN Al8Si3Cu ALLOY |
3 |
| EFFECTS OF ELECTROMAGNETIC FREQUENCY AND SIC NANOPARTICLES ON THE MICROSTRUCTURE REFINEMENT AND MECHANICAL PROPERTIES OF Al A357-1.5 WT% SIC NANOCOMPOSITES |
3 |
| EFFECT OF SILICON AND MICROSTRUCTURE ON SPHEROIDAL GRAPHITE CAST IRON THERMAL CONDUCTIVITY AT ELEVATED TEMPERATURES |
3 |
| EFFECT OF CO AND NI ADDITION ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES AT ROOM AND ELEVATED TEMPERATURE OF AN Al-7%Si ALLOY |
2 |
| DIMENSIONAL CONTROL OF NICKEL-BASED SINGLE CRYSTAL TURBINE BLADE INVESTMENT CASTING BY PROCESS CONTROL OPTIMIZATION |
2 |
| EXPERIMENTAL INVESTIGATION AND OPTIMIZATION OF PROCESS PARAMETERS FOR IMPACT STRENGTH OF COMPOUND CAST BIMETALLIC JOINTS |
2 |
| OPTIMIZATION OF THE STRONTIUM MODIFICATION PROCESS IN GRAVITY PERMANENT MOULD TILT CAST AlSi6Cu4 CYLINDER HEADS |
2 |
| EFFECT OF Sr-GRAIN REFINER-Si INTERACTIONS ON THE MICROSTRUCTURE CHARACTERISTICS OF Al-Si HYPEREUTECTIC ALLOYS |
2 |
| STUDY OF HOT TEARING IN STAINLESS STEEL CF3M DURING CASTING USING SIMULATION AND EXPERIMENTAL METHOD |
2 |
| EFFECT OF COATING LAYER OF SAND CASTING MOLD IN THIN-WALLED DUCTILE IRON CASTING: REDUCING THE SKIN EFFECT FORMATION |
2 |
| INCLUSION MEASUREMENT AND IDENTIFICATION IN MG-BASED ALLOYS: APPLICATION OF THE BRIGHTIMETER TECHNIQUE |
2 |
| METALLURGICAL AND MECHANICAL CHARACTERIZATION OF A319 ALUMINUM ALLOY CASTING SOLIDIFIED UNDER MOLD OSCILLATION |
2 |
| ON THE IMPACT PROPERTIES AND FRACTOGRAPHY OF AL-11%SI CASTING ALLOY |
2 |
| BETA Al5FeSi PHASE PLATELETS-POROSITY FORMATION RELATIONSHIP IN A319.2 TYPE ALLOYS |
2 |
| Identifying Cast Iron Microstructure Variation Using Acoustic Resonance Techniques |
2 |
| Ultrasonic Melt Treatment of Light Alloys |
2 |
| EFFECT OF CA ON THE Y CONTENT AND CYCLIC OXIDATION BEHAVIOR OF Ni-BASED SINGLE-CRYSTAL SUPERALLOY |
2 |
| AlSi5Mg0.3 ALLOY FOR THE MANUFACTURE OF AUTOMOTIVE WHEELS |
2 |
