| Comparison of grey wolf, whale, water cycle, ant lion and sine-cosine algorithms for the optimization of a vehicle engine connecting rod |
45 |
| The Harris hawks optimization algorithm, salp swarm algorithm, grasshopper optimization algorithm and dragonfly algorithm for structural design optimization of vehicle components |
33 |
| The Harris hawks, grasshopper and multi-verse optimization algorithms for the selection of optimal machining parameters in manufacturing operations |
33 |
| A new hybrid Harris hawks-Nelder-Mead optimization algorithm for solving design and manufacturing problems |
29 |
| Experimental investigation on mechanical properties of AA7075-AlN composites |
22 |
| Lightweight design of an automobile hinge component using glass fiber polyamide composites |
19 |
| An investigation of the crash performance of magnesium, aluminum and advanced high strength steels and different cross-sections for vehicle thin walled energy absorbers |
18 |
| A new hybrid approach for reliability-based design optimization of structural components |
18 |
| An experimental and numerical investigation of the effects of geometry and spot welds on the crashworthiness of vehicle thin-walled structures |
17 |
| Topography and topology optimization of diesel engine components for light-weight design in the automotive industry |
13 |
| Mechanical properties of friction stir welded St 37 and St 44 steel joints |
12 |
| Optimization of cryogenic treatment effects on the surface roughness of cutting tools |
12 |
| Effects of process parameters on the quality of PLA products fabricated by fused deposition modeling (FDM): surface roughness and tensile strength |
8 |
| Dry sliding behavior of aluminum alloy 8011 with 4 % fly ash |
5 |
| Microstructure and mechanical properties of fly ash particulate reinforced AA8011 aluminum alloy composites |
5 |
| Effect o stir spot residual Alclad on friction welds of AA2219 alloys |
5 |
| Mode based correlation between change of electrical resistance and change of dislocation density of fatigued-loaded ICE R7 wheel steel specimens |
5 |
| Effect of Cr content on microstructure and mechanical properties of carbidic austempered ductile iron |
4 |
| Dry sliding behavior of the aluminum alloy 8011 composite with 8% fly ash |
4 |
| Mechanical and tribological behavior of SiC and fly ash reinforced Al 7075 composites compared to SAE 65 bronze |
4 |
| Mechanical properties characterization of resistance spot welded DP1000 steel under uniaxial tensile tests |
4 |
| Optimization of surface roughness via the Taguchi method and investigation of energy consumption when milling spheroidal graphite cast iron materials |
4 |
| Optimization and characterization of friction surfaced coatings of ferrous alloys |
3 |
| Mechanical properties of waste mussel shell particles reinforced epoxy composites |
3 |
| Mechanical properties of 16 different FDM-plastic types |
3 |
| StressLife(tc) - NDT-related assessment of the fatigue life of metallic materials |
3 |
| SteBLife - A new short-time procedure for the calculation of S-N curves and failure probabilities |
3 |
| Effect of rhenium and cobalt additions on the microstructure and gamma prime phase stability of vacuum arc melted modified nickel-based superalloys grade MGA 1400 |
3 |
| Hoop tensile and compression behavior of glass-carbon intraply hybrid fiber reinforced filament wound composite pipes |
3 |
| Tensile strength of 3D printed materials: Review and reassessment of test parameters |
3 |
| Tool condition monitoring in the milling process with vegetable based cutting fluids using vibration signatures |
3 |
| Characterization of the boron layer formed by pack boronizing of binary iron-niobium alloys |
3 |
| Effect of austenitizing temperature on the microstructure evolution and properties of Cu-bearing CADI |
3 |
| Effects of clay and silica nanoparticles on the Charpy impact resistance of a carbon/aramid fiber reinforced epoxy composite |
3 |
| Energy consumption model for the pipe threading process using 10 wt.-% Cu and 316L stainless steel powder-reinforced aluminum 6061 fittings |
3 |
| Microstructure, mechanical properties and ELM based wear loss prediction of plasma sprayed ZrO2-MgO coatings on a magnesium alloy |
2 |
| Corrosion fatigue assessment of extruded magnesium alloys AZ31 and ME20 |
2 |
| Low heat input welding of nickel superalloy GTD-111 with Inconel 625 filler metal |
2 |
| Optimization of welding parameters for DP600/TRIP800 dissimilar joints |
2 |
| Fatigue behavior and mechanism of KMN in a very high cycle regime |
2 |
| Hygrothermal environment effects on mechanical properties of T700/3228 CFRP laminates |
2 |
| Test procedure for stress damage of ferromagnetic materials based on metal magnetic memory effects |
2 |
| Thermography using a 1D laser array - From planar to structured heating |
2 |
| Microstructure and mechanical properties of nano-carbon reinforced Cu-based powder metallurgy friction materials produced by hot isostatic pressing |
2 |
| Non-metallic inclusions and fatigue strength of steel 34CrNiMo6 |
2 |
| Compression testing of additively manufactured continuous carbon fiber-reinforced sandwich structures |
2 |
| Effects of induction hardened surface depth on the dynamic behavior of rotating shaft systems |
2 |
| Determination of the Johnson-Cook damage parameter D-4 by Charpy impact testing |
2 |
| Wear resistance of laser cladded Stallite 31 coating on AISI 316L steel |
2 |
| Effect of seawater on pin-loaded laminated composites |
2 |
