| A Study of the Structure, Mechanical Properties and Corrosion Resistance of Magnesium Alloy WE43 After Rotary Swaging |
7 |
| Fabrication, Structure and Properties of a Composite from Aluminum Matrix Reinforced with Carbon Nanofibers |
6 |
| Tailoring the Properties in Functionally Graded Alloy Inconel 718 Using Additive Technologies |
4 |
| Macrostructure and Mechanical Properties of Al - Si, Al - Mg - Si, and Al - Mg - Mn Aluminum Alloys Produced by Electric Arc Additive Growth |
4 |
| Effect of Radial Shear Rolling on the Structure and Mechanical Properties of a New-Generation High-Strength Aluminum Alloy Based on the Al - Zn - Mg - Ni - Fe System |
4 |
| Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Friction Stir Processed AZ91D Magnesium Alloy |
4 |
| High Plastic Deformations and High Cooling Rates at the Interface of Explosion-Welded Materials |
4 |
| A STUDY OF REDISTRIBUTION OF SILICON IN DUAL-PHASE SILICON STEELS |
4 |
| New Method of Severe Plastic Deformation of Metals |
3 |
| STRUCTURAL-MORPHOLOGICAL FLUCTUATIONS INDUCED BY THERMOMECHANICAL TREATMENT IN A Fe - Mn - Si SHAPE MEMORY ALLOY |
3 |
| Effect of Electron Beam Power Density on the Structure of Titanium Under Non-Vacuum Electron-Beam Treatment |
3 |
| Modeling and Optimization of the Effect of Sintering Parameters on the Hardness of Copper/Graphene Nanosheet Composites by Response Surface Methodology |
3 |
| Effect of Heat Treatment on the Structure and Phase Composition of a High-Temperature Nickel Alloy Obtained by Laser Cladding |
3 |
| Panoramic Crystallographic Analysis of Structure Evolution in Low-Carbon Martensitic Steel under Tempering |
2 |
| Special Features of Precipitation of epsilon-Cu Phase in Cast Irons Alloyed with Copper and Aluminum |
2 |
| Effect of Initial Structural State on Formation of Structure and Mechanical Properties of Steels Under ECAP |
2 |
| Texture Formation in Hot Rolling of Electrical Anisotropic Steel |
2 |
| Effect of Post Weld Heat Treatment on Strength and Microstructure of Friction Stir Welded Lap Joints of AA2014-T6 Aluminum Alloy |
2 |
| INFLUENCE OF THE CHEMICAL COMPOSITION OF Al/AlC/a-C:H COATINGS ON THE MECHANICAL PROPERTIES OF MAGNESIUM ALLOY AZ31 |
2 |
| Raising the Corrosion Resistance of Plasma-Nitrided Steel 45 (AISI 1045) by Preliminary Sandblasting |
2 |
| Structure and Properties of Functional Self-Fluxing Nickel-Containing Coatings Obtained by Non-Vacuum Electron-Beam Cladding |
2 |
| Effect of Hardening Heat Treatment on the Structure and Properties of a Three-Layer Composite of Type VT23-08ps-45KhNM' Obtained by Explosion Welding |
2 |
| RAILROAD RAILS FROM BAINITIC STEEL |
2 |
| Microstructure and Mechanical Properties of Welds of Al - Mg - Si Alloys After Different Modes of Impulse Friction Stir Welding |
2 |
| Effect of Nitriding on the Wear Resistance of Tool Powder Steels with Different Contents of V, Cr and Mo |
2 |
| Criteria for Evaluating the Fracture Toughness of Carbon-Carbon Composite Materials |
2 |
| Effect of Hot Rolling Rate on the Structure and Texture Condition of Plates of the Al - Si - Mg Alloy System |
2 |
| QUANTITATIVE ANALYSIS OF DOMAIN STRUCTURE AND RAPID SEARCH FOR NEW MATERIALS FOR PERMANENT MAGNETS |
2 |
| Development of Heat-Resistant Aluminum Alloys for Electrical Engineering Purposes Based on the Al - Fe - Si System |
2 |
| Comparative Analysis of Non-Uniformity of Mechanical Properties of Welded Joints of Al - Mg - Si Alloys During Friction Stir Welding and Laser Welding |
2 |
| Technological and Operational Features of Drill Pipes from Aluminum Alloys 2024 and 1953 |
2 |
| Design of Castable Refractory Nickel Alloys with Polycrystalline Structure |
1 |
| Microstructure and Wear of a Sintered Composite with a Magnesium Alloy AZ91 Matrix Reinforced with ZrO2 Particles |
1 |
| Phase Transformations in Single-Crystal Refractory Nickel Alloy with Tantalum, Rhenium and Ruthenium Additions |
1 |
| Arrangement of Collective B-12 Atoms in the Crystal Structure of gamma-Fe and Effect of Boron on the Hardenability of Steel |
1 |
| VARIATION OF THE COMPOSITION AND PROPERTIES OF CEMENTITE IN HEAT TREATMENT OF TILLING MACHINE MEMBERS FROM CHILLED CAST IRON |
1 |
| About the Nature of Quasi-Cleavage in Low-Carbon Steel Embrittled with Hydrogen |
1 |
| Effect of SiO2 Nanoparticles and Soluble Silicate on the Composition and Properties of Oxide Layers Formed by Microarc Oxidizing on Magnesium Mg96 |
1 |
| CORROSION RESISTANCE OF STEEL 45 SUBJECTED TO ELECTROMECHANICAL TREATMENT AND SURFACE PLASTIC DEFORMATION |
1 |
| Effect of the Chemical Composition of Powder Stock on the Strength of Materials After Selective Laser Melting |
1 |
| Ultrasonic Methods for Improving Object Surface Quality Prepared by Corrosion-Resistant Steel Powder Selective Laser Melting |
1 |
| Study of the Breakage Region of High Ductility Steel 08G2B Charpy Specimen Fracture |
1 |
| Transformations of Supercooled Austenite in Promising High-Hardenability Machine Steels |
1 |
| Primary Recrystallization Texture in FCC-Metal with Low Packing Defect Energy |
1 |
| Effect of Crystal Lattice Parameters of Surface Gas-Saturated Layers on Ductility of Titanium Alloys Under Tensile Tests |
1 |
| STRUCTURE AND PROPERTIES OF R - (Fe, Co) - B (R = Nd, Dy, Ho) PE ANENT MAGNETS WITH LOW TEMPE TURE COEFFICIENT OF INDUCTION |
1 |
| Morphology of High-Strength Heat-Resistant Steel Powder for Machines for Additive Production from Shavings |
1 |
| A Study of Modes of Hardening Heat Treatment of Titanium Alloy VT23 |
1 |
| Effect of Medium-Temperature Additional Tempering on the Carbide Phase and Cold Resistance of Heat-Hardenable Steel 09G2SA-A |
1 |
| A Study of Structural Features of a Gradient Material from a Heat-Resistant Nickel Alloy Produced by Laser Cladding |
1 |
