| Effect of the welding environment and storage time of electrodes on the diffusible hydrogen content in deposited metal |
8 |
| The removal of toxic metals from liquid effluents by ion exchange resins. Part IX: Lead(II)/H plus /Amberlite IR-120 |
5 |
| Service life prediction for 50-year-old buildings in marine environments |
4 |
| The removal of toxic metals from liquid effluents by ion exchange resins. Part X: Antimony(III) /H+/Ionac SR7 |
3 |
| The removal of toxic metals from liquid effluents by ion exchange resins. Part VIII: Arsenic(III)/OH-/Dowex 1x8 |
3 |
| The removal of toxic metals from liquid effluents by ion exchange resins. Part XI: Cobalt(II)/H+/Lewatit TP260 |
3 |
| The removal of toxic metals from liquid effluents by ion exchange resins. Part VI: Manganese(II)/H+/Lewatit K2621 |
3 |
| The removal of toxic metals from liquid effluents by ion exchange resins. Part VII: Manganese(VII)/H+/Amberlite 958 |
3 |
| Application of Rietveld Refinement to the correlation of the microstructure evolution of white cast irons with 18 and 25 %-wt. Cr after oil quench and successive temper treatments, with abrasive wear and bending testing |
2 |
| Analysis of artificial aging with induction and energy costs of 6082 Al and 7075 Al materials |
2 |
| Finite element modelling to predict reinforced concrete corrosion-induced cracking |
2 |
| An investigation into the wear behavior of aged Alumix321/SiC composites fabricated by hot pressing |
1 |
| Influence of heat input on the Charpy ductile fracture behavior of reheated HAZ in GMAW multilayer welded joints on HSLA steel using digital fractographic analysis |
1 |
| Study on extraction of light rare earth from liquid - liquid extraction using organophosphoric acids extractants and ascorbic acid |
1 |
| Microstructural evolution and dynamic strain aging (DSA) of Mg-6% Gd-1% Zn alloy during tension and compression testing at intermediate temperatures |
1 |
| The mechanical and tribological characteristic of Aluminium-Titanium dioxide composites |
1 |
| Permanent magnets and its production by powder metallurgy |
1 |
| Ultrasonic evaluation of the formed phases in a duplex stainless steel 2205 heat treated at 750 degrees C and corrosion behavior |
1 |
| Mapping initial stages of localized corrosion of AA6061-T6 in diluted substitute ocean water by LEIS and SKP |
1 |
| Effects of concentrated solar irradiation on allotropic transformations of AISI 316 stainless steel |
0 |
| Effect of cobalt on zinc oxide nanoparticles in the anticorrosive performance of an alkyd primer |
0 |
| A further study of the kinetics of recrystallization and grain growth of cold rolled TWIP steel |
0 |
| Influence of the nanotubular morphology on the wettability and contact angle of Ti6Al4V ELI alloy |
0 |
| Natural liquid-extract of morinda citrifolia as corrosion inhibitor for steels (AISI-1045) exposed to acidic environments of HCl |
0 |
| Structural studies of evolution of solid solutions of BaTiO3 doped with Er (3+) (solid-state reaction method) |
0 |
| Comparative study of AISI 4340 and AISI 347 nitrocarburizing by Tenifer-QPQ (R) process |
0 |
| Quality increase for single-welded joints of thin-walled structures by means of simulation modelling |
0 |
| Influence of pre-deformation on the precipitation hardening in Cu-Ni-Si alloy |
0 |
| Effect of ZrO2 and L-Cys nanoparticles as dopants in sol-gel of mesoporous silica coating for corrosion protection of AZ61 magnesium alloy |
0 |
| Corrosion of 1050 aluminium in coastal atmospheres |
0 |
| The effect of precipitation of metastable phases on the thermophysical and mechanical properties of the EN AW-6082 alloy |
0 |
| Microstructural characterization and finite element modeling of AZ31 magnesium alloys welded joints |
0 |
| Consideration of cold metal transfer welding of AA5754 to galvanized steel from mechanical and microstructural aspects |
0 |
| Study of the thickness evolution during SPT Testing |
0 |
| Dissolution kinetics of calcined ulexite in ammonium sulfate solutions |
0 |
| Influence of the roughening method, joint configuration and adhesive thickness on the shear strength of ferritic stainless steel surfaces joined by methyl methacrylate |
0 |
| Microstructural optimization of unalloyed ductile cast irons with a ferritic matrix used in the manufacture of wind turbine rotors |
0 |
| Microstructural analysis of hypoeutectic white cast iron coatings with Si and V additions |
0 |
| Development of the a phase in alpha series of Al-Cu-Zn alloys according to their size and mechanical properties generated by increased Al-Cu and aging treatment |
0 |
| Evolution and process of manufacture of NEO magnets applied to motors of electric vehicles |
0 |
| Influence of an ERNiCrMo-3 root pass on the properties of cast iron weld joints |
0 |
| A common and concise formats approach to a Key-Curve construction for generating crack extension data in C(T) specimens |
0 |
| Ammoniacal Carbonate Leaching: Estimation of dissolved nickel in the distillation effluent |
0 |
| Assessment of the mechanical behaviour of thermally aged B and Fe modified CuZnAl shape memory alloys |
0 |
| Design and characterization of three light-weight multi-principal-element alloys potentially candidates as high-entropy alloys |
0 |
| Statistical analysis of the coating thickness of duplex protection systems during the accelerated climatic test of humidity and controlled temperature |
0 |
| Changes in the microstructure and passive layer of 2024-T3 Al-Cu alloy during a chemical cleaning employed in the aerospace industry |
0 |
| Study of phase decomposition during spark plasma sintering of Al-5% Ni3Al composites |
0 |
| Teaching how to determine the Charpy impact according to the general requirements defined in part-UG of the ASME VIII code division 1 |
0 |
