| Numerical Simulation-Based Optimization of Contact Stress Distribution and Lubrication Conditions in the Straight Worm Drive |
6 |
| Contact Deformation Behavior of an Elastic Silicone/SiC Abrasive in Grinding and Polishing |
5 |
| Probabilistic Fatigue Crack Initiation and Propagation Fields Using the Strain Energy Density |
4 |
| In-Service Degradation of Mechanical Characteristics of Pipe Steels in Gas Mains |
4 |
| Adhesive Pull and Shear Strength of Epoxy Nanocomposite Coatings Filled with Ultradispersed Diamond |
4 |
| Effect of a Nonuniform Radial/Axial Tip Clearance on the Flow Field in a Mixed-Flow Pump |
3 |
| Solution of a Transverse Plane Bending Problem of a Laminated Cantilever Beam Under the Action of a Normal Uniform Load |
3 |
| Numerical Simulation of the Stress-Strain State of Thin-Layer Rubber-Metal Vibration Absorber Elements Under Nonlinear Deformation |
3 |
| STUDY OF BOND PROPERTIES OF STEEL REBARS WITH RECYCLED AGGREGATE CONCRETE. EXPERIMENTAL TESTING |
3 |
| ASSESSMENT OF HYDROGEN EMBRITTLEMENT IN HIGH-ALLOY CHROMIUM-NICKEL STEELS AND ALLOYS IN HYDROGEN AT HIGH PRESSURES AND TEMPERATURES |
3 |
| Generalized Diagram of the Ultimate Nominal Stresses (Endurance Limit) and the Corresponding Dimensions of the Non-Propagating Fatigue Cracks for Sharp and Blunt Notches |
3 |
| Comparative Analysis of Processing Techniques' Effect on the Strength of Carbon Black (N220)-Filled Poly (Lactic Acid) Composites |
3 |
| Improvement of Microstructure, Hardness, and Mechanical Properties of Cobalt-Based Amorphous Coating Via Laser Cladding |
2 |
| OPTIMIZATION OF RESIDUAL STRESSES IN LASER-MIXED WC(Co, Ni) COATINGS |
2 |
| Hot Extrusion Effect on the Microstructure and Mechanical Properties of a Mg-Y-Nd-Zr Alloy |
2 |
| Short Fatigue Crack Behavior of LZ50 Axle Steel Under Rotating-Bending Cyclic Loading |
2 |
| MICROSTRUCTURE AND MICROWAVE ABSORPTION PROPERTIES OF CEMENT-BASED MATERIAL REINFORCED WITH REDUCED GRAPHENE OXIDE AND NANOPARTICLES |
2 |
| Optimum Plans of Step-Stress Life Tests Using Failure-Censored Data Form Burr Type-Xii Distribution |
2 |
| Effect of Coatings on the Fatigue Characteristics of Steels Under Contact Load |
2 |
| Acidic-Thermal Ageing Effect on Compression Stress Relaxation of Silicone Rubber |
2 |
| STUDY OF COMPOSITE FIBER REINFORCEMENT OF CRACKED THIN-WALLED PRESSURE VESSELS UTILIZING MULTI-SCALING TECHNIQUE BASED ON EXTENDED FINITE ELEMENT METHOD |
2 |
| Finite Element Analysis of Thermoelastic Fiber-Reinforced Anisotropic Hollow Cylinder with Dual-Phase-Lag Model |
2 |
| Study on High-Strength Ring Chain Dynamic Characteristics Under Different Launch Parameters |
2 |
| STUDY OF BOND PROPERTIES OF STEEL REBARS WITH RECYCLED AGGREGATE CONCRETE. ANALYTICAL MODELING |
2 |
| Fatigue Damage Analysis of an Asphalt Mixture Based on Pseudostiffness |
2 |
| Assessment of the Microstructure and Mechanical Properties of a Laser-Joined Carbon Fiber-Reinforced Thermosetting Plastic and Stainless Steel |
2 |
| Real-Time Substructure Tests and Numerical Simulation of Mechanical Characteristics of Natural Rubber-Laminated Bearings |
2 |
| Properties and Applications of the Electrohydraulic Servosystem of the Hydraulic Excavator |
2 |
| Numerical Simulation of the Thermomechanical Behavior of a Hot Stamping Die |
1 |
| Structural Strength and Service Life of the Extrusion Forming Die for Agricultural Engine Piston Heads |
1 |
| Friction and Wear Behavior of Wear-Resistant Belts in Drill Joints for Deep and Ultra-Deep Wells |
1 |
| Electron Backscatter Diffraction Analysis of the Microstructure Fineness in Pure Copper Under Torsional Deformation |
1 |
| Mechanical Properties of Dissimilar A356/SAPH440 Lap Joints by the Friction Stir Spot Welding and Self-Piercing Riveting |
1 |
| Effect of Cyclic Stresses Below the Endurance Limit on the Fatigue Life of 40Cr Steel |
1 |
| A Setup for Complex Investigation of Mechanical Characteristics of Structural Materials for NPP Equipment |
1 |
| Study on the Cracking Mechanism of YQ450NQR1 High-Strength Weathering Steel |
1 |
| A Simulation Study on the Effect of Cavity Shapes on the Penetration of Linear Shaped Charges with Curved Liners |
1 |
| Methods for the Simulation of the Aerodynamic Heating Conditions of the Structural Elements of Space Shuttles |
1 |
| Mathematical Prediction of Strength of Ablating Polymer Unidirectional Composites in Transverse Direction and in Shear Along and Across Fibers |
1 |
| Modified KT-Diagram for Stress Raiser-Involved Fatigue Strength Assessment |
1 |
| Effect of Si and Mn on Microstructure and Mechanical Properties of Vacuum Suction Casting Al-4.5Cu Alloy |
1 |
| Effect of Shock and Vibration Preloading on the Parameters of Tear Dimples and their Conglomerates |
1 |
| Development of Graphene Nanoplatelets-Reinforced Thermo-Responsive Shape Memory Nanocomposites for High Recovery Force Applications |
1 |
| Physical Simulation-Based Characterization of HAZ Properties in Steels. Part 1. High-Strength Steels and Their Hardness Profiling |
1 |
| Determination of the Mechanical Characteristics of the Metal of the Equipment of Nuclear Power Stations from Hardness Measurement and Indentation Data |
1 |
| Enhancement of the Unified Constitutive Model for Viscoplastic Solders in Wide Strain Rate and Temperature Ranges |
1 |
| Effect of Heat Treatment on Relative Change in the Young Modulus of D16 Alloy Under the Action of Low Cyclic Loads |
1 |
| EXPERIMENTAL INVESTIGATION OF VISCOELASTIC CHARACTERISTICS OF RUBBER-CORD COMPOSITES CONSIDERING THE PROCESS OF THEIR SELF-HEATING |
1 |
| STRESS-STRAIN ASSESSMENT FOR LAMINATED AIRCRAFT COCKPIT WINDOWS AT STATIC AND DYNAMIC LOADS |
1 |
| Determination of Effective Characteristics of the Fibrous Viscoelastic Composite with Transversal and Isotropic Components |
1 |
