| Recent developments in high-strength Mg-RE-based alloys: Focusing on Mg-Gd and Mg-Y systems |
92 |
| Review of magnesium-based biomaterials and their applications |
80 |
| Overview of advancement and development trend on magnesium alloy |
45 |
| Kinetics in Mg-based hydrogen storage materials: Enhancement and mechanism |
36 |
| Magnesium matrix composites for biomedical applications |
36 |
| A review: Past, present and future of grain refining of magnesium castings |
25 |
| Review on friction stir welding of magnesium alloys |
23 |
| Corrosion behavior of Mg-Mn-Ca alloy: Influences of Al, Sn and Zn |
22 |
| Effect of Y and Gd content on the microstructure and mechanical properties of Mg-Y-RE alloys |
19 |
| Potential of multi-pass ECAP on improving the mechanical properties of a high-calcium-content Mg-Al-Ca-Mn alloy |
19 |
| Corrosion resistance of bioinspired DNA-induced Ca-P coating on biodegradable magnesium alloy |
18 |
| Fabrication of corrosion-resistant superhydrophobic coating on magnesium alloy by one-step electrodeposition method |
18 |
| Mechanical and metallurgical properties of friction stir welded dissimilar joints of AZ91 magnesium alloy and AA 6082-T6 aluminium alloy |
17 |
| Superhydrophobic surface of Mg alloys: A review |
17 |
| Introduction to magnesium alloy processing technology and development of low-cost stir casting process for magnesium alloy and its composites |
16 |
| Comparison of microstructures and mechanical properties of composite extruded AZ31 sheets |
16 |
| Enhancing strength and creep resistance of Mg-Gd-Y-Zn-Zr alloy by substituting Mn for Zr |
16 |
| Effect of Sn addition on the mechanical properties and bio-corrosion behavior of cytocompatible Mg-4Zn based alloys |
15 |
| Effects of cold and warm cross-rolling on microstructure and texture evolution of AZ31B magnesium alloy sheet |
14 |
| Effect of hot rolling on microstructure and properties of the ZEK100 alloy |
14 |
| A review of magnesium die-castings for closure applications |
14 |
| Influence of heat treatment on the machinability and corrosion behavior of AZ91 Mg alloy |
14 |
| Improved tensile properties of AZ31 Mg alloy subjected to various caliber-rolling strains |
13 |
| Corrosion rate determination of rare-earth Mg alloys in a Na2SO4 solution by electrochemical measurements and inductive coupled plasma-optical emission spectroscopy |
13 |
| High temperature mechanical behavior of low-pressure sand-cast Mg-Gd-Y-Zr magnesium alloy |
13 |
| Influence of tool pin profile and rotational speed on the formation of friction stir welding zone in AZ31 magnesium alloy |
12 |
| Twinning behavior of hot extruded AZ31 hexagonal prisms during uniaxial compression |
12 |
| Evaluation of self-healing properties of inhibitor loaded nanoclay-based anticorrosive coatings on magnesium alloy AZ91D |
12 |
| Corrosion behavior of Mg-3Gd-1Zn-0.4Zr alloy with and without stacking faults |
12 |
| The corrosion behavior of AZ31 alloy in chloride and sulfate media - A comparative study through electrochemical investigations |
11 |
| Effects of trace Ca/Sn addition on corrosion behaviors of biodegradable Mg-4Zn-0.2Mn alloy |
11 |
| Microstructural evolution, mechanical properties, and corrosion resistance of a heat-treated Mg alloy for the bio-medical application |
11 |
| Investigation of microstructure and mechanical properties of friction stir welded AZ61 magnesium alloy joint |
11 |
| Investigation on dry sliding wear behavior of Mg/BN nanocomposites |
11 |
| Effect of applied pressure on microstructures of squeeze cast Mg-15Gd-1Zn-0.4Zr alloy |
10 |
| Microstructure and texture evolution of AZ31 Mg alloy after uniaxial compression and annealing |
10 |
| Influence of processing route on microstructure and wear resistance of fly ash reinforced AZ31 magnesium matrix composites |
10 |
| Wear and mechanical characterization of Mg-Gr self-lubricating composite fabricated by mechanical alloying |
10 |
| Microstructure and texture evolution in LZ91 magnesium alloy during cold rolling |
10 |
| Precipitation modification in cast Mg-1Nd-1Ce-Zr alloy by Zn addition |
9 |
| Strain hardening behavior of Mg-Y alloys after extrusion process |
9 |
| Study of the degradation behavior and the biocompatibility of Mg-0.8Ca alloy for orthopedic implant applications |
9 |
| Influence of tool rotation speeds on mechanical and morphological properties of friction stir processed nano hybrid composite of MWCNT-Graphene-AZ31 magnesium |
9 |
| The flow behavior in as-extruded AZ31 magnesium alloy under impact loading |
9 |
| Investigation of ZrO2 nanoparticles concentration and processing time effect on the localized PEO coatings formed on AZ91 alloy |
9 |
| Growth behaviour of low-energy plasma electrolytic oxidation coatings on a magnesium alloy |
9 |
| Super-hydrophobic stearic acid layer formed on anodized high purified magnesium for improving corrosion resistance of bioabsorbable implants |
9 |
| Fabrication of ultra-high strength magnesium alloys over 540 MPa with low alloying concentration by double continuously extrusion |
8 |
| Evaluation of electrochemical impedance and biocorrosion characteristics of as-cast and T4 heat treated AZ91 Mg-alloys in Ringer's solution |
8 |
| Statistical optimization of stress level in Mg-Li-Al alloys upon hot compression testing |
8 |
