| Solder joint quality evaluation based on heating factor |
7 |
| Initial conditions-related dynamical behaviors in PI-type memristor emulator-based canonical Chua's circuit |
5 |
| Novel implementation of IoT based non-invasive sensor system for real-time monitoring of intravenous fluid level for assistive e-healthcare |
5 |
| Synchronization, anti-synchronization and circuit realization of a novel hyper-chaotic system |
5 |
| Chaos in a second-order non-autonomous Wien-bridge oscillator without extra nonlinearity |
4 |
| ISFET structures with chemically modified membrane for bovine serum albumin detection |
3 |
| Characterization of a novel 10T SRAM cell with improved data stability and delay performance for 20-nm tri-gated FinFET technology |
3 |
| Design and analysis of cantilever based piezoelectric vibration energy harvester |
3 |
| Fractal-based triangular bandpass filter with a notched band for interference rejection in wideband applications |
2 |
| A low-PDAP and high-PSNR approximate 4:2 compressor cell in CNFET technology |
2 |
| Pencil-on-paper flexible electronics for daily sensing applications |
2 |
| Design of a novel triple-band monopole antenna for WLAN/WiMAX MIMO applications in the laptop computer |
2 |
| Investigation of inkjet printed path resistance in the context of manufacture and flexible application |
1 |
| Effects of microstrip line fabrication and design on high-speed signal integrity transmission of PCB manufacturing process |
1 |
| Smart home for elder care using wireless sensor |
1 |
| Dynamic impedance compensation for WPT using a compensator in a three-coil wireless power transfer system |
1 |
| Technological aspects of silver particle sintering for electronic packaging |
1 |
| Low computation digital down converter using polyphase IIR filter |
1 |
| A chaotic circuit under a new classification framework of inductorless Chua's circuits |
1 |
| Experimental verification of volt-ampere characteristic curve for a memristor-based chaotic circuit |
1 |
| Modelling of temperature distribution along PCB thickness in different substrates during reflow |
1 |
| Transfer characteristics of the MCR-WPT system using two series transmitting coils |
0 |
| Improvement of plating uniformity for copper patterns of IC substrate with multi-physics coupling simulation |
0 |
| Influential mechanism of printed circuit board properties on micro hole drilling temperature |
0 |
| Frequency changing technique for efficient fast start-up RF energy harvesting |
0 |
| Design and experimental analysis of MEMS-based Ku band phase shifter |
0 |
| Low power LC-voltage controlled oscillator with-140 dBc/Hz @ 1 MHz offset using on-chip inductor design in 0.13 mu m RF-CMOS process for S-Band application |
0 |
| Performance analysis of differential spin hall effect (DSHE)-MRAM-based logic gates |
0 |
| Evaluation of a compact triangular crinkle-shaped multiband antenna with circular polarized for ITU band based on MADM method |
0 |
| Design of K-band modified hairpin filter with harmonic suppression using GaAs MMIC process |
0 |
| Using uniform magnetic field to obtain the constant output power and transfer efficiency for MCR-WPT |
0 |
| A reliable model for the compensation loop of multistage amplifiers at high frequency |
0 |
| Cryogenic auxiliary drilling of printed circuit boards |
0 |
| Variability aware FinFET SRAM cell with improved stability and power for low power applications |
0 |
| Novel symmetrical step-down topologies of zigzag autotransformer |
0 |
| Numerical simulation and experiments to improve throwing power for practical PCB through-holes plating |
0 |
| An 8kW LLC resonant converter in plasma power supply based on SiC power devices for efficiency improvement |
0 |
| Statistical data analysis for harmonic reduction in 3o-fragmented source using novel fuzzy digital logic switching technique |
0 |
| Techniques of impedance matching for minimal PCB channel loss at 40 GBPS signal transmission |
0 |
| Electrochemical and analytical study of electroplating additive in copper plating solution for microvia filling |
0 |
| A novel hybrid series stacked differential fractal inductor for MMIC applications |
0 |
| Thermal stability analysis of passive components embedded into printed circuit boards |
0 |
| Packing density of inkjet printed paths |
0 |
| Thermal interface materials based on graphene and silver nanopowder |
0 |
| Effects of CCL inorganic filler on hole performance in PCB drilling process |
0 |
| The influence of properties of printed circuit board resin and filler on drilling force |
0 |
| A broadband 23.1 similar to 27.2 GHz doherty power amplifier with peak output power of 24.3 dBm |
0 |
| Laser micro-machined 28 GHz broad band single feed microstrip antenna for 5G mm-wave applications |
0 |
| Optimal design of RAM cell using novel 2:1 multiplexer in QCA technology |
0 |
| Sleep signal controlled footless domino circuit for low leakage current |
0 |
