| Profit maximization in reverse logistics based on disassembly scheduling using hybrid bee colony and bat optimization |
30 |
| Influence of surface roughness in turning process - an analysis using artificial neural network |
26 |
| Mechanical, wear and thermal behaviour of hemp fibre/egg shell particle reinforced epoxy resin bio composite |
12 |
| Sensitivity analysis and optimization of EDM process parameters |
5 |
| Auto-ignition characteristics of diesel fuel in an O-2-CO2 mixture |
4 |
| Application of computational fluid dynamics for thermohydrodynamic analysis of high-speed squeeze-film dampers |
3 |
| Hydrokinetic turbine array modeling for performance analysis and deployment optimization |
3 |
| Experimental investigation on hole quality in drilling of composite pipes |
3 |
| Kinematic analysis of a newly designed cable-driven manipulator |
3 |
| Influence of tool rotational speed on microstructural characteristics of dissimilar Mg alloys during friction stir welding |
2 |
| Nonsingular terminal sliding mode control of underwater remotely operated vehicles |
2 |
| Early bearing fault diagnosis based on improved SFLA and ELM network (Retracted article. See vol. pg. 2019) |
2 |
| Robust control for permanent magnet in-wheel motor in electric vehicles using adaptive fuzzy neural network with inverse system decoupling |
2 |
| A brief review of condition monitoring techniques for the induction motor |
2 |
| Roller-rail parameters on the transverse vibration characteristics of super-high-speed elevators |
2 |
| A statistical model of elastic-plastic contact between rough surfaces |
2 |
| Comprehensive compensation method for thermal error of vertical drilling center |
2 |
| Simplification of the dynamic model of a hydraulic rockbreaker for implementation in a model-based control scheme |
2 |
| Influence of design parameters on the singularities and workspace of a 3-RPS parallel robot |
2 |
| Inclined landing testing of an omni-directional unmanned aerial vehicle |
2 |
| Dynamic analysis and optimization of a kinematically redundant planar parallel manipulator |
2 |
| Performance assessment of Darrieus wind turbines with symmetric and cambered airfoils |
2 |
| Numerical study of the effect of gas-to-liquid ratio on the internal and external flows of effervescent atomizers |
1 |
| Reliability modeling for competing failure systems with instant-shift hard failure threshold |
1 |
| VAWT versus HAWT: a comparative performance study of 2-6 MW rated capacity turbines |
1 |
| Vibration stability analysis of dual motor harmonic synchronous excitation nonlinear vibration conveyer |
1 |
| Quantification of uncertainty associated with wind assessments of various intervals |
1 |
| Towards the appropriate synthesis of the four-bar linkage |
1 |
| Design of a novel deployable mechanism for capturing tumbling debris |
1 |
| Geometric optimization of a self-adaptive robotic leg |
1 |
| Analysis of load distribution and contact stiffness of the single-nut ball screw based on the whole rolling elements model |
1 |
| Properties and fracture splitting of cast steel matrix composites |
1 |
| Development and simulation of magnetorheological damper for segment erector vibration control |
1 |
| Burr edge occupancy: edge finishing index for milling machined parts |
1 |
| Nonlinear dynamics analysis of rotor-brush seal system |
1 |
| Gearbox fault diagnosis via generalized velocity synchronous Fourier transform and order analysis |
1 |
| Research on load identification of mine hoist based on improved support vector machine |
1 |
| A hybrid high-performance trajectory tracking controller for unmanned hexrotor with disturbance rejection |
1 |
| Consideration of interlaminar strain-energy continuity in composite plate analysis using improved higher order theory |
1 |
| Simulation and experiment of vibrational or acoustic communication in mining and oil-gas drill strings |
1 |
| An experimental study on wearing of conical picks interacting with rock |
1 |
| Design of grinding wheel profile for new micro drill flute |
0 |
| Design and development of tractor clutch using combined field and bench tests |
0 |
| Feedforward control for underactuated bipedal walking on varying compliant slopes |
0 |
| A lower limb exoskeleton based on recognition of lower limb walking intention |
0 |
| Wake measurements of oscillating supercritical airfoil in compressible flow |
0 |
| Optimum run parameters in cold strip rolling |
0 |
| New solid particle seeding generator for laser-based velocity measurements in reacting flows |
0 |
| Dynamic modeling of aircraft landing gear and multi-objective optimization with simple cell mapping method |
0 |
| Ground mobile Bennett mechanism |
0 |
